MAX1479ATE+T【PDF 6/10 页】IC TRANSM ASK/FSK 16-TQFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录55

2页 3页 4页 5页 [6页]7页 8页 9页 10页

300MHz to 450MHz Low-Power,

Crystal-Based +10dBm ASK/FSK Transmitter

6 _______________________________________________________________________________________

Detailed Description

The MAX1479 is a highly integrated ASK/FSK transmit-

ter operating over the 300MHz to 450MHz frequency

band. The device requires only a few external compo-

nents to complete a transmitter solution. The MAX1479

includes a complete PLL and a highly efficient power

amplifier. The device can be set into a 0.2nA low-power

shutdown mode.

Shutdown Mode

ENABLE (pin 4) is internally pulled down with a 20礎

current source. If it is left unconnected or pulled low,

the MAX1479 goes into a low-power shutdown mode.

In this mode, the supply current drops to 0.2nA. When

ENABLE is high, the device is enabled and is ready for

transmission after 200祍 (frequency settles to within

50kHz).

The 200祍 turn-on time of the MAX1479 is mostly domi-

nated by the crystal oscillator startup time. Once the

oscillator is running, the 300kHz PLL bandwidth allows

fast frequency recovery during power-amplifier toggling.

Mode Selection

MODE (pin 2) sets the MAX1479 in either ASK or FSK

mode. When MODE is set low, the device operates as

an ASK transmitter. If MODE is set high, the device

operates as an FSK transmitter. In the ASK mode, the

DIN pin controls the output of the power amplifier. A

logic low on DIN turns off the PA, and a logic high turns

on the PA. In the FSK mode, a logic low on the DIN pin

is represented by the low FSK frequency, and a logic-

high input is represented by the high FSK frequency.

(The ASK carrier frequency and the lower FSK frequen-

cy are the same.) The deviation is proportional to the

crystal load impedance and pulling capacitance. The

maximum frequency deviation is 55kHz for f

315MHz and 80kHz for f

= 433MHz.

Pin Description

NAME

DESCRIPTION

Supply Voltage. Bypass to GND with a 10nF and 220pF capacitor as close to the pin as possible.

MODE

Mode Select. A logic low on MODE enables the device in ASK mode. A logic high on MODE enables the

device in FSK mode.

DIN

Data Input. Power amplifier is on when DIN is high in ASK mode. Frequency is high when DIN is high in

FSK mode.

ENABLE Standby/Power-Up Input. A logic low on ENABLE sets the device in standby mode.

CLKOUT Buffered Clock Output. Programmable through CLK0 and CLK1. See Table 1.

DD_

Power-Amplifier Supply Voltage. Bypass to GND with a 10nF and 220pF capacitor as close to the pin as

possible.

ROUT

Envelope-Shaping Output. ROUT controls the power-amplifier envelope rise and fall. Bypass to GND with a

680pF and 220pF capacitor as close to the pin as possible.

PAOUT

Power-Amplifier Output. Requires a pullup inductor to the supply voltage, which can be part of the output-

matching network to an antenna.

CLK0

1st Clock Divider Setting. See Table 1.

CLK1

2nd Clock Divider Setting. See Table 1.

DEV0

1st FSK Frequency-Deviation Setting. See Table 2.

DEV1

2nd FSK Frequency-Deviation Setting. See Table 2.

DEV2

3rd FSK Frequency-Deviation Setting. See Table 2.

XTAL1

1st Crystal Input. f

= 32 x f

XTAL

XTAL2

2nd Crystal Input. f

= 32 x f

XTAL

GND

Ground. Connect to system ground.

Exposed Ground Pad. EP is the power amplifiers ground. It must be connected to PCB through a low-

inductance ath.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式